NFPA Hazard Ratings:

Emergency Overview: CAUTION:Irritation of exposed tissues

Potential Health Effects:

• Signs and Symptoms of Acute Overexposure: Irritation of exposed tissues
• Signs and Symptoms of Chronic overexposure: NDA
• Medical Conditions Generally Aggravated by Exposure: Ingestion may cause severe allergic reaction in some asthmatics.

• Inhalation: Remove patient to fresh air
• Ingestion: Give patient 2 - 4 glasses of water or milk to drink to dilute the product. Induce vomiting by tickling the back of the throat. Get medical advice.
• Skin Contact: Remove contaminated clothing and footwear. Wash skin with soap and water. Wash clothing before reuse.
• Eye Contact: Immediately flush eyes with water for 15 minutes. Get medical attention.
• Note to Physician: None

Flash Point: NA

Flammability Limits: NA

Autoignition temp: NA

Fire Extinguishing Media: Water spray, carbon dioxide, dry chemical

Special Fire-Fighting Information: Wear NIOSH-approved SCNA. Use water spray to cool containers and to knock down fumes.

Unusual Fire and Explosion Hazards: Sulfur dioxide as may be released if sodium sulfite is heated above 900 degrees C.

• Ventilation System: Good general ventilation is advisable
• Personal Respirators (NIOSH Approved): if needed, use respirator to screen out nuisance dust
• Skin Protection: Long sleeved clothing and cotton gloves
• Eye Protection: Chemical safety goggles if dust is raised
• Other Control Measures: Minimize exposure in accordance with good hygiene practice. Avoid handling which would create large amounts of dust.

• Appearance and Color: White granular powder , flecked with pink.
• Odor: None
• Solubility in Water: 17% @ 10 degrees C
• Specific Gravity: 2.63
• pH: 9.8
• % volatile by volume @ 21C (70F): Nil
• Boiling Point: NA
• Melting Point: NA
• Vapor Density (Air=1): NA
• Vapor Pressure (mm Hg): NA
• Evaporation Rate (Bu. Acetate=1): NA

• Stability: Product is stable.
• Hazardous Decomposition Products: Sulphur dioxide gas, sodium sulfide residue
• Hazardous Polymerization: will not occur.
• Incompatibility: Acids, strong oxidizers.
• Conditions to Avoid: NDA

• Toxicological Data:

RTECS: CAS # 7757-83-7: WE2150000 / CAS# 10124-43-3:GG5100000

LD50 /LC50: CAS 7757-83-7: Oral, mouse:LD50 = 820 mg/kg / CAS# 10124-43-3: Oral, rat LD50 = 424 mg/Kg /

• Carcinogenicity: Ingredients not listed by ACGIH, IARC, NIOSH, NTR, or OSHA

 Environmental Fate: NDA

Environmental Toxicity: NDA

• DOT Proper Shipping Name: Not regulated as hazardous by DOT
• DOT Hazard Class: None
• DOT Label: N/A

• TSCA: :(40CFR 710) All chemical ingredients are listed on the TSCA 8(b) inventory. None of the ingredients are on the Health and Safety Reporting List, are under Chemical Test rule, are listed under TSCA Section 12B, or have a SNUR under TSCA
• CERCLA Reportable Quantity: This product does NOT contain ingredients that have Reportable Quantity (RQ) requirements under US 40 CFR 117.302
• SARA TITLE III:

..................................Section 302/304 Extremely Hazardous Substances: None

..................................Section 311 Hazard Categorization: Acute, health

..................................Section 313 Toxic Chemicals: None

• FDA: This product complies with 21 CFR 184.1139 regulations for boiler water additives used in preparation of steam that will contact food.
• Clean Water Act: Ingredients not listed as hazardous pollutants under CWA.
• Clean Air Act:Cobalt sulfate, CAS 10124-43-3 IS listed as a "hazardous air pollutant", but is not a Class 1 or Class 2 "ozone depletors" lists published by CAA.
• STATE RIGHT TO KNOW REGULATIONS: Ingredients are NOT listed on the following RTK lists: California, Florida, Illinois, Louisiana, Maine, Maryland, Massachusetts, Minnesota, New Jersey, New York, Pennsylvania, or Rhode Island.
• California Proposition 65 Labeling required for this surfactant: This product contains <1%,, Cobalt sulfate, CAS# 10124-43-3, a chemical known to the state of California to cause cancer or birth defects, requiring that this notification be added to MSDS and product labels for product shipped into the state of California.
• Canadian WHMIS: None for product as a whole, with pH of 9.2. Sodium hydroxide would normally incur a class "E", but its low concentration does not affect classification of product.
• Canadian DSL: All ingredients listed on the Canadian DSL. Product is approved for sale in Canada
• Canada's Ingredient Disclosure Cobalt sulfate, CAS 10124-43-3, comprising < 1% of this product IS listed on the CIDL, but other ingredients are "NOT CONTROLLED". This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.
  

Reason for Revision: Routine review & Revision

Alken-Murray Corporation provides the information contained herein in good faith, in compliance with the Occupational Safety and Health Act of 1970, but makes no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Alken-Murray warrants that this product is of merchantable quality. The implied warranty of fitness for a particular purpose is limited to the extent the products are used for the purpose or uses described on the product's label or in any written instructions or materials distributed to the buyer by Alken-Murray and is hereby disclaimed should buyer use the products in a manner inconsistent with this uses or purposes described therein. In no event shall Alken-Murray be liable for any consequential, exemplary, or incidental damages incurred by buyer even if it has been advised of the possibility of such damages.